##----------------------------------------------------------------------------- ## base.txt - fli4l configuration parameters 2.0.3 ## ## You can edit/change this file with fliwiz V1.6 or any text editor. ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 26.03.2002 jm ## ## Copyright (c) 2001-2002 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # General settings: #------------------------------------------------------------------------------ HOSTNAME='HP-Router' # name of fli4l router PASSWORD='xxxxx' # password for telnetd, ftpd and sshd MOUNT_BOOT='rw' # mount boot device (floppy): ro, rw, no RAMSIZE='' # size of ramdisk for unzipped opt.tgz # the variables MOUNT_OPT, PART_OPT and UPDATE_MODE will be ignored if # RAMSIZE is not empty. see docu MOUNT_OPT='rW' # mount opt device: ro, rw PART_OPT='hda2' # location of opt-files? ram1 or disk-partition UPDATE_MODE='full' # add, cfg, full, none, see documentation #------------------------------------------------------------------------------ # Ethernet card drivers: # uncomment your ethernet card #------------------------------------------------------------------------------ ETH_DRV_N='2' # number of ethernet drivers to load, usually 1 #ETH_DRV_1='3c505' # ISA: 3COM Etherlink Plus (3c505) #ETH_DRV_1='3c507' # ISA: 3COM Etherlink 16 (3c507) #ETH_DRV_1='3c509' # ISA: 3COM EtherLinkIII (3c509) #ETH_DRV_1='3c515' # ISA: 3COM EtherLink XL ISA (3c515) #ETH_DRV_1='3c59x' # PCI: 3COM Vortex/Boomerang 3c59x,3c900,3c905 #ETH_DRV_1='82596' # Apricot Xen-II on board Ethernet #ETH_DRV_1='3c503' # ISA: 3COM EtherLinkII (3c503) #ETH_DRV_1='e2100' # ISA: Cabletron E21xx ISA #ETH_DRV_1='hp' # ISA: HP PCLAN (27245, 27xxx) ISA #ETH_DRV_1='hp-plus' # ISA: HP PCLAN+ (27247B and 27252A) ISA #ETH_DRV_1='ne' # ISA: NE2000 ISA clone (eg. Realtek 8019, # Accton 16xx, NatSemi 8390, UMC 9003/9008) #ETH_DRV_1='ne2k-pci' # PCI: NE2000 PCI clone (eg. Realtek 8029, # Winbond 89c940) #ETH_DRV_1='smc-ultra' # ISA: SMC ULTRA #ETH_DRV_1='smc-ultra32' # EISA: SMC ULTRA32 (NEW) #ETH_DRV_1='wd' # ISA: SMC WD80*3 #ETH_DRV_1='at1700' # ISA: AT1700 (Fujitsu 86965) ISA #ETH_DRV_1='cs89x0' # ISA: IBM Etherjet, cs89x0 based Cards (Option io=0xnnn necessary!) #ETH_DRV_1='de4x5' # PCI/EISA: Digital DE425, DE434, DE435, DE450, DE500 #ETH_DRV_1='depca' # ISA: DEPCA, DE10x, DE200, DE201, DE202, DE422 #ETH_DRV_1='dgrs' # PCI: Digi International RightSwitch PCI/EISA #ETH_DRV_1='dmfe' # PCI: DM9102 compatible PCI cards from Davicom #ETH_DRV_1='elp486' # ISA: Intel Professional Workstation/panther 82596 #ETH_DRV_1='eepro' # ISA: Intel EtherExpress Pro/10 #ETH_DRV_1='eepro100' # PCI: Intel EtherExpressPro PCI 10+/100B/100+ #ETH_DRV_1='eexpress' # ISA: EtherExpress16 ISA #ETH_DRV_1='epic100' # PCI: SMC EPIC/100 (EtherPower II) PCI #ETH_DRV_1='eth16i' # ISA/EISA: ICL EtherTeam 16i/32 #ETH_DRV_1='ewrk3' # ISA: EtherWORKS 3 ISA (DE203, DE204, DE205) #ETH_DRV_1='fealnx' # PCI: ASOUND LAN 8139 card - not RTL8139 (NEW) #ETH_DRV_1='hp100' # ISA/EISA/PCI: HP 10/100VG PCLAN (ISA, EISA, PCI) #ETH_DRV_1='lance' # ISA: AMD LANCE and PCnet (AT1500, NE2100) ISA #ETH_DRV_1='old_tulip' # PCI: Old DECchip Tulip (dc21x4x) PCI ETH_DRV_2='pcnet32' # PCI: AMD PCI PCnet32 #ETH_DRV_1='rtl8139-orig' # PCI: RealTek 8129/8139 (not 8019/8029!) #ETH_DRV_1='rtl8139' # PCI: RealTek 8129/8139 (not 8019/8029!) (NEW) ETH_DRV_1='8139too' # PCI: RealTek 8139 10/100 MB (NEW) #ETH_DRV_1='sis900' # PCI: SiS 900/7016 #ETH_DRV_1='sundance' # PCI: DFE-550FX or DFE-530TXS (NEW) #ETH_DRV_1='tlan' # PCI: TI ThunderLAN (Compaq Netelligent ...) #ETH_DRV_1='tulip' # PCI: DECchip Tulip (dc21x4x) PCI #ETH_DRV_1='natsemi' # PCI: Nat Semi #ETH_DRV_1='starfire' # PCI: Starfire #ETH_DRV_1='via-rhine' # PCI: VIA Rhine PCI (3043, VT86c100A, dfe-530tx) #ETH_DRV_1='winbond-840' # PCI: Winbond 840 #ETH_DRV_1='lanstreamer' # Token Ring: IBM Auto LANStreamer PCI Adapter #ETH_DRV_1='olympic' # Token Ring: IBM cards (Pit/Pit-Phy/Olympic) #ETH_DRV_1='ibmtr' # Token Ring: IBM 16/4 #ETH_DRV_1='pcnet_cs' # PCMCIA: NS8390-based cards (NE2000, DLINK etc) #ETH_DRV_1='3c574_cs' # PCMCIA: 3Com 574 #ETH_DRV_1='3c575_cb' # PCMCIA: 3Com 575 #ETH_DRV_1='3c589_cs' # PCMCIA: 3Com 589 #ETH_DRV_1='airo' # PCMCIA: Airo 4500 & 4800 series cards #ETH_DRV_1='airo_cs' # PCMCIA: Airo 4500 & 4800 series cards #ETH_DRV_1='eepro100_cb' # PCMCIA: EtherExpress Pro 100 #ETH_DRV_1='epic_cb' # PCMCIA: SMC 83c170 EPIC/100 #ETH_DRV_1='ibmtr_cs' # PCMCIA: IBM Token Ring #ETH_DRV_1='netwave_cs' # PCMCIA: Netwave AirSurfer Wireless LAN #ETH_DRV_1='nmclan_cs' # PCMCIA: New Media Ethernet LAN #ETH_DRV_1='ray_cs' # PCMCIA: Raylink wireless cards #ETH_DRV_1='smc91c92_cs' # PCMCIA: SMC91c92-based cards #ETH_DRV_1='tulip_cb' # PCMCIA: DEC 21040-family cards #ETH_DRV_1='wavelan_cs' # PCMCIA: WaveLAN #ETH_DRV_1='wavelan2_cs' # PCMCIA: WaveLAN2 #ETH_DRV_1='wvlan_cs' # PCMCIA: Lucent WaveLAN/IEEE 802.11 #ETH_DRV_1='xirc2ps_cs' # PCMCIA: Xircom: CE2, CEM28, CEM33, or CE3 #ETH_DRV_1='wl24_cs' # PCMCIA: ELSA Airlancer MC-2 #ETH_DRV_1='cs89x0_cs' # PCMCIA: IBM EtherJet Ethernet Adapter ETH_DRV_1_OPTION='' # additional option, e.g. 'io=0x340' for ne ETH_DRV_2_OPTION='' # additional option, e.g. 'io=0x340' for ne #------------------------------------------------------------------------------ # Ether networks used with IP protocol: #------------------------------------------------------------------------------ IP_ETH_N='1' # number of ip ethernet networks, usually 1 IP_ETH_1_NAME='' # optional: other device name than ethX IP_ETH_1_IPADDR='192.168.0.88' # IP address of your n'th ethernet card IP_ETH_1_NETWORK='192.168.0.0' # network of your LAN IP_ETH_1_NETMASK='255.255.255.0' # netmask of your LAN #------------------------------------------------------------------------------ # Additional routes, optional #------------------------------------------------------------------------------ IP_DEFAULT_GATEWAY='' # normally not used, read documentation! IP_ROUTE_N='0' # number of additional routes IP_ROUTE_1='192.168.7.0 255.255.255.0 192.168.6.99' # network netmask gateway #------------------------------------------------------------------------------ # Masquerading: #------------------------------------------------------------------------------ MASQ_NETWORK='192.168.0.0/24' # networks to masquerade (e.g. our LAN) MASQ_MODULE_N='14' # load n masq modules (default: only ftp) MASQ_MODULE_1='ftp' # ftp MASQ_MODULE_2='h323' # h323 (netmeeting) MASQ_MODULE_3='icq' # icq (use with caution!) MASQ_MODULE_4='irc' # irc MASQ_MODULE_5='raudio' # raudio MASQ_MODULE_6='vdolive' # vdolive MASQ_MODULE_7='quake' # quake MASQ_MODULE_8='cuseeme' # cuseeme MASQ_MODULE_9='mms' # MSN-Filetransfer MASQ_MODULE_10='pptp' # pptp MASQ_MODULE_11='ipsec' # ipsec MASQ_MODULE_12='dplay' # dplay (direct play) MASQ_MODULE_13='msn-0.02' # msn zone (use version 0.01 or 0.02) MASQ_MODULE_14='udp_dloose' # pseudo mod: some internet games need it MASQ_FTP_PORT_N='0' # using ftp masq-module on different ports MASQ_FTP_PORT_1='21' # standard ftp port MASQ_FTP_PORT_2='2021' # additional port #------------------------------------------------------------------------------ # Optional package: PORTFW # # If you set OPT_PORTFW='yes', you can also edit opt/etc/portfw.sh #------------------------------------------------------------------------------ OPT_PORTFW='yes' # install port forwarding tools/modules PORTFW_N='0' # how many portforwardings to set up PORTFW_1='80 192.168.0.99:80 tcp' # sample 1: forward ext. port 8080 to int. # host 192.168.6.15 to port 80 (use tcp) PORTFW_2='3000-3010 192.168.6.15 tcp' # sample 2: forward portrange to int. host # 192.168.5.15 (use tcp) #------------------------------------------------------------------------------ # Routing without masquerading #------------------------------------------------------------------------------ ROUTE_NETWORK='' # optional: route from/to network, no masq #------------------------------------------------------------------------------ # Routing: internal hosts to deny forwarding #------------------------------------------------------------------------------ FORWARD_DENY_HOST_N='0' # number of denied hosts FORWARD_DENY_HOST_1='192.168.6.5' # optional: 1st denied host FORWARD_DENY_HOST_2='192.168.6.6' # optional: 2nd denied host #------------------------------------------------------------------------------ # Routing: ports to reject/deny forwarding (from inside and outside!) #------------------------------------------------------------------------------ FORWARD_DENY_PORT_N='1' # no. of ports to reject/deny forwarding FORWARD_DENY_PORT_1='137:139 REJECT' # deny/reject forwarding of netbios FORWARD_TRUSTED_NETS='' # but allow forwarding between LANs #------------------------------------------------------------------------------ # Firewall: ports to reject/deny from outside (all served ports) # # here we leave two ports untouched: # # 53 dns # 113 auth #------------------------------------------------------------------------------ FIREWALL_DENY_PORT_N='8' # no. of ports to reject/deny FIREWALL_DENY_PORT_1='0:52 REJECT' # privileged ports: reject or deny FIREWALL_DENY_PORT_2='54:79 REJECT' # privileged ports: reject or deny FIREWALL_DENY_PORT_3='81:112 REJECT' # privileged ports: reject or deny FIREWALL_DENY_PORT_4='114:1023 REJECT' # privileged ports: reject or deny FIREWALL_DENY_PORT_5='5000:5001 REJECT' # imond/telmond ports: reject or deny FIREWALL_DENY_PORT_6='8000 REJECT' # proxy access: reject or deny FIREWALL_DENY_PORT_7='10000 REJECT' # WebMin fuer EisFair: reject or deny FIREWALL_DENY_PORT_8='20012 REJECT' # vbox server access: reject or deny FIREWALL_DENY_ICMP='no' # deny icmp (ping): yes or no FIREWALL_LOG='yes' # log access to rejected/denied ports #------------------------------------------------------------------------------ # Domain configuration: #------------------------------------------------------------------------------ START_DNS='yes' # start dns server: yes or no DNS_FORWARDERS='145.253.2.11' # DNS servers of your provider, e.g. NexGo #Die IP-Adressen lauten 145.253.2.11 oder 145.253.2.75 (151.189.0.65) DNS_VERBOSE='no' # log queries in /usr/local/ens/ens.log DOMAIN_NAME='jome.de' # your domain name DNS_FORBIDDEN_N='0' # number of forbidden domains DNS_FORBIDDEN_1='foo.bar' # 1st forbidden domain DNS_FORBIDDEN_2='bar.foo' # 2nd forbidden domain HOSTS_N='5' # number of hosts in your domain HOST_1='192.168.0.88 HP-Router' # 1st host: ip and name HOST_2='192.168.0.1 Mond' # 2nd host: ip and name HOST_3='192.168.0.2 Sonne' # 3rd host: ip and name HOST_4='192.168.0.3 Erde' # 4th host: ip and name HOST_5='192.168.0.99 Suse' # Suse-Server #HOST_6='192.168.0.4 Erde ' # Ersatz #HOST_7='192.168.0.5 Erde ' # Ersatz #------------------------------------------------------------------------------ # Special DNS configuration #------------------------------------------------------------------------------ DNS_N='0' # number of special dns servers, normally 0 #DNS_1='firma.de 192.168.1.12' # 1st special dns server for firma.de #DNS_2='lan.firma.de 192.168.2.12' # 2nd special dns server for lan.firma.de #------------------------------------------------------------------------------ # imond configuration: #------------------------------------------------------------------------------ START_IMOND='yes' # start imond: yes or no IMOND_PORT='5000' # TCP-Port, see also FIREWALL_DENY_PORT_x! IMOND_PASS='' # imond-password, may be empty IMOND_ADMIN_PASS='xxxxx' # imond-admin-password, may be empty IMOND_LED='com3' # tty for led: com1 - com4 or empty IMOND_BEEP='yes' # beep if connection going up/down IMOND_LOG='yes' # log /var/log/imond.log: yes or no IMOND_LOGDIR='/var/log' # log-directory, e.g. /var/log IMOND_ENABLE='yes' # accept "enable/disable" commands IMOND_DIAL='yes' # accept "dial/hangup" commands IMOND_ROUTE='yes' # accept "route" command IMOND_REBOOT='yes' # accept "reboot" command #------------------------------------------------------------------------------ # Generic circuit configuration: #------------------------------------------------------------------------------ IP_DYN_ADDR='yes' # use dyn. ip addresses (most providers do) DIALMODE='auto' # standard dialmode: auto, manual, or off #------------------------------------------------------------------------------ # optional package: syslogd #------------------------------------------------------------------------------ OPT_SYSLOGD='yes' # start syslogd: yes or no SYSLOGD_DEST_N='2' # number of destinations SYSLOGD_DEST_1='*.* /dev/console' # n'th prio & destination of syslog msgs SYSLOGD_DEST_2='*.* @192.168.0.2' # example: loghost 192.168.6.2 SYSLOGD_DEST_3='kern.info /var/log/dial.log' # example: log infos #------------------------------------------------------------------------------ # optional package: klogd #------------------------------------------------------------------------------ OPT_KLOGD='yes' # start klogd: yes or no #------------------------------------------------------------------------------ # optional package: y2k correction #------------------------------------------------------------------------------ OPT_Y2K='no' # y2k correction: yes or no Y2K_DAYS='' # correct hardware Y2K-Bug: add x days #------------------------------------------------------------------------------ # Optional package: PNP #------------------------------------------------------------------------------ OPT_PNP='no' # install isapnp tools: yes or no ##----------------------------------------------------------------------------- ## dsl.txt - fli4l configuration parameters 2.0.3 ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 25.02.2002 jm ## ## Copyright (c) 2001-2002 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: PPPoE #------------------------------------------------------------------------------ OPT_PPPOE='yes' # use ppp over ethernet: yes or no PPPOE_NAME='ArcorDSL' # circuit name, don't write spaces PPPOE_USEPEERDNS='no' # use dns server of your provider: yes or no PPPOE_ETH='eth1' # eth card connected to ADSL modem, e.g. 2nd PPPOE_USER='xxxxxxxx' # username PPPOE_PASS='xxxx' # password PPPOE_DEBUG='no' # enable pppd debugging, 'yes' or 'no' PPPOE_HUP_TIMEOUT='600' # idle time after which to hangup PPPOE_CHARGEINT='60' # value of charge interval (in seconds) PPPOE_TIMES='Mo-Su:00-24:0.0:Y' # times/charges when LCR #------------------------------------------------------------------------------ # Optional package: PPTP - DSL in Austria/Netherlands #------------------------------------------------------------------------------ OPT_PPTP='no' # use PPP over ethernet: yes or no PPTP_NAME='DSL' # circuit name, don't write spaces PPTP_USEPEERDNS='no' # use dns server of your provider: yes or no PPTP_ETH='eth1' # ethernet card connected to ADSL modem PPTP_USER='anonymer' # username PPTP_PASS='surfer' # password PPTP_DEBUG='no' # enable pppd debugging, 'yes' or 'no' PPTP_HUP_TIMEOUT='600' # idle time after which to hangup PPTP_MODEM_TYPE='bcaa' # 2 different types in Austria: bbaa / bcaa # in the Netherlands use 'mxstream' PPTP_CHARGEINT='60' # value of charge interval (in seconds) PPTP_TIMES='Mo-Su:00-24:0.0:Y' # times/charges when LCR #---------------------------------------------------------------------------- # optional package: PPPoE-Status #---------------------------------------------------------------------------- OPT_POESTATUS='no' # show pppoe status on console #3 ##----------------------------------------------------------------------------- ## easyEASYCRON.txt - fli4l configuration parameters V2.2 ## ## ## Creation: 08.11.2001 fm ## Last Update: 16.03.2002 jm ## ## Copyright (c) 2001 Stephan Manske ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- # #------------------------------------------------------------------------------ # Optional package: EASYCRON #------------------------------------------------------------------------------ OPT_EASYCRON='yes' # EASYCRON: yes or no EASYCRON_NOMAIL='yes' # EASYCRON: yes or no - Mail von cron unterdrücken EASYCRON_N='1' # EASYCRON: Anzahl EASYCRON_1_CUSTOM='' # EASYCRON: eigene Einstellungen wie Umgebungsvariablen EASYCRON_1_COMMAND='/usr/local/bin/tuxtime.sh JoMe xxx 1611 >/dev/null' # EASYCRON: auszuführender Befehl EASYCRON_1_TIME='0 * * * *' # EASYCRON: Zeitpunkt: zu jeder vollen Stunde ##----------------------------------------------------------------------------- ## hd.txt - fli4l configuration parameters 2.0.3 ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 26.03.2002 jm ## ## Copyright (c) 2001 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional: mount additional devices #------------------------------------------------------------------------------ OPT_MOUNT='yes' # mount disks or cdroms: yes or no MOUNT_N='1' # number of mounts MOUNT_1_DEV='hda3' # example: 4th partition of first ide-hard disk MOUNT_1_FS='ext2' # filesystem type: vfat, ext2, iso9660 or swap MOUNT_1_POINT='/usr/local/data' # mount point, here: /usr/local/data MOUNT_1_CHECK='yes' # check/repair filesystem if corrupted: yes, no MOUNT_1_OPTION='rw' # additional options, see documentation! #------------------------------------------------------------------------------ # Optional package: HDINSTALL #------------------------------------------------------------------------------ OPT_HDINSTALL='no' # install on harddisk: yes or no #------------------------------------------------------------------------------ # Optional package: FDISK #------------------------------------------------------------------------------ OPT_FDISK='no' # create partitions manually #------------------------------------------------------------------------------ # Optional package: Modes for IDE Harddisk #------------------------------------------------------------------------------ OPT_HDTUNE='no' # power down HD after some time HDTUNE_N='1' # number of drives to change modes HDTUNE_DISK_1='hda' # drive to handle HDTUNE_SLEEP_1='yes' # sleep mode: yes or no HDTUNE_SLEEPTIME_1='2' # wait 2 minutes until power down HDTUNE_32BIT_1='yes' # 32 BIT IO on: yes or no HDTUNE_DMA_1='yes' # DMA ACCESS: yes or no HDTUNE_READLA_1='yes' # Read-Lookahead: yes or no #------------------------------------------------------------------------------ # Optional package: RESCUE #------------------------------------------------------------------------------ OPT_RESCUE='yes' # install e2fsck #------------------------------------------------------------------------------ # Optional package: CDROM (only for ide, for scsi see additional package scsi) #------------------------------------------------------------------------------ OPT_CDROM='yes' # install IDE CDROM drivers: yes or no ##----------------------------------------------------------------------------- ## httpd.txt - fli4l configuration parameters 2.0.3 ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 25.02.2002 jm ## ## Copyright (c) 2001 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: HTTP-Server for Monitoring #------------------------------------------------------------------------------ OPT_HTTPD='yes' # install mini web server: yes or no HTTPD_PORT='81' # http port, see also FIREWALL_DENY_PORT_x ! HTTPD_DOC_ROOT='' # directory with content for the httpd HTTPD_ADMIN_DIR='admin' # dir of the webserver for the admin-interface HTTPD_USER_N='1' # number of users for the HTTPD-server HTTPD_USER_1='xxxx' # name of the 1st user HTTPD_PASS_1='xxxx' # password of the 1st user HTTPD_RIGHTS_1='all' # rights of the 1st user ##----------------------------------------------------------------------------- ## inet.txt - fli4l configuration parameters 2.0.3 ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 25.02.2002 jm ## ## Copyright (c) 2001 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: TELNETD #------------------------------------------------------------------------------ OPT_TELNETD='yes' # install telnetd: yes or no TELNETD_PORT='23' # telnet port, see also FIREWALL_DENY_PORT_x #------------------------------------------------------------------------------ # Optional package: SSHD (secure shell) #------------------------------------------------------------------------------ OPT_SSHD='yes' # install sshd: yes or no SSHD_PORT='22' # ssh port, see also FIREWALL_DENY_PORT_x #------------------------------------------------------------------------------ # Optional package: FTPD #------------------------------------------------------------------------------ OPT_FTPD='yes' # install ftpd: yes or no FTPD_PORT='21' # ftp port, see also FIREWALL_DENY_PORT_x ##----------------------------------------------------------------------------- ## isdn.txt - fli4l configuration parameters 2.0.3 ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 25.02.2002 jm ## ## Copyright (c) 2001 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: ISDN #------------------------------------------------------------------------------ OPT_ISDN='yes' # use ISDN: yes or no ISDN_TYPE='9' # type, e.g. Teles 16.3 ISA ISDN_IO='0x398' # io, e.g. 0xd80 for Teles 16.3 ISA ISDN_IO0='' # io0 ISDN_IO1='' # io1 ISDN_MEM='' # mem ISDN_IRQ='10' # irq, e.g. 12 for Teles 16.3 ISA ISDN_DEBUG_LEVEL='31' # debug level (hisax driver) ISDN_VERBOSE_LEVEL='2' # verbose level #---------------------------------------------------------------------------- # ISDN compression (EXPERIMENTAL): #---------------------------------------------------------------------------- OPT_ISDN_COMP='no' # use LZS or BSD compression: 'yes' or 'no' ISDN_LZS_DEBUG='1' # debug level lzscomp (0..3) ISDN_LZS_COMP='8' # compression level lzscomp (0..9) ISDN_LZS_TWEAK='7' # tweak lzscompr (at present: 0..7) #---------------------------------------------------------------------------- # ISDN Circuits: #---------------------------------------------------------------------------- ISDN_CIRCUITS_N='1' # no. of ISDN circuits, DSL: see pppoe.txt #---------------------------------------------------------------------------- # Circuit 1: Internet-By-Call-Provider MSN #---------------------------------------------------------------------------- ISDN_CIRC_1_NAME='ArcorFlat' # circuit MSN ISDN_CIRC_1_USEPEERDNS='no' # use dns server of your provider: yes or no ISDN_CIRC_1_TYPE='ppp' # circuit uses sync ppp (ipppd) ISDN_CIRC_1_BUNDLING='yes' # channel bundling: yes or no ISDN_CIRC_1_BANDWIDTH='6144 30' # if bundling=yes: opt. bandwidth on demand ISDN_CIRC_1_LOCAL='' # local ip address of your ISDN card - dummy ISDN_CIRC_1_REMOTE='' # remote ip address (ISDN) - dummy ISDN_CIRC_1_NETMASK='255.255.255.0' # netmask (ISDN) - dummy ISDN_CIRC_1_MTU='1500' # max transmission unit (use 1500 if comp!) ISDN_CIRC_1_MRU='1524' # maximum receive unit ISDN_CIRC_1_COMPRESSION='yes' # compress headers/frames, see docum. ISDN_CIRC_1_FRAMECOMP='default' # type of framecompression, see docum. ISDN_CIRC_1_IPX_NETWORK='' # optional: ipx network ISDN_CIRC_1_IPX_NODE='' # optional: ipx nodes local:remote ISDN_CIRC_1_REMOTENAME='' # optional: remote hostname for dialin ISDN_CIRC_1_USER='xxx' # User-ID to login into provider's gateway ISDN_CIRC_1_PASS='xxxx' # Password for login ISDN_CIRC_1_ROUTE='0.0.0.0' # this is the default route ISDN_CIRC_1_DIALOUT='019xxxx' # dialout: ISDN number of provider ISDN_CIRC_1_DIALIN='' # dialin: no dialin ISDN_CIRC_1_CALLBACK='off' # callback mode: 'in', 'out', or 'off' ISDN_CIRC_1_CBDELAY='3' # callback delay, only used for callbacks ISDN_CIRC_1_EAZ='32684137' # your MSN (without area code) ISDN_CIRC_1_SLAVE_EAZ='' # optional slave MSN for channel bundling ISDN_CIRC_1_DEBUG='yes' # enable ipppd debugging, 'yes' or 'no' ISDN_CIRC_1_AUTH='' # require the peer to authenticate itself ISDN_CIRC_1_HUP_TIMEOUT='600' # Hangup after 45 seconds idle time ISDN_CIRC_1_CHARGEINT='60' # Value of charge interval (in seconds) ISDN_CIRC_1_TIMES='Mo-Fr:09-18:0.0:N Mo-Fr:18-09:0.0:N Sa-Su:00-24:0.0:N' # times/charges when LCR #------------------------------------------------------------------------------ # telmond configuration: #------------------------------------------------------------------------------ OPT_TELMOND='yes' # start telmond: yes or no TELMOND_PORT='5001' # TCP-Port, see also FIREWALL_DENY_PORT_x! TELMOND_LOG='yes' # log /var/log/telmond.log: yes or no TELMOND_LOGDIR='/var/log' # log-directory, e.g. /var/log TELMOND_MSN_N='0' # number of msn->ip mapping entries TELMOND_MSN_1='123 192.168.6.2' # e.g. map MSN 123 to client 192.168.6.2 TELMOND_CMD_N='0' # no. of commands to be executed if call-in TELMOND_CMD_1='123 * sleep 5; imonc dial' # e.g. dial out via default circuit ##----------------------------------------------------------------------------- ## lcd.txt - fli4l configuration parameters 2.0.3 ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 25.02.2002 jm ## ## Copyright (c) 2001 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: LCD #------------------------------------------------------------------------------ OPT_LCD='yes' # install lcd driver and tools: yes or no LCD_COLS='20' # no. of lcd columns (16,20,32,40) dflt: 20 LCD_LINES='4' # no. of lcd lines (1,2,4) dflt: 4 LCD_ADDRESS='0x0278' # IO address of used lpt port, or 'comX' LCD_TIME_LONG='' # long delay time (empty = default: 100) LCD_TIME_SHORT='' # short delay time (empty = default: 40) LCD_OPTION='' # set 'a_type=1', if you have a HD66712 chip LCD_START_ISDN_RATE='yes' # isdn/dsl rating display on lcd: yes or no LCD_TYPE_N='0' # no. of data types to show, see docum. LCD_TYPE_ONLINE_N='13' # no. of data types to show if online LCD_TYPE_ONLINE_1=' 8 0 0' # DSL status channel 1 LCD_TYPE_ONLINE_2='39 7 0 :' # Text LCD_TYPE_ONLINE_3='31 9 0' # DSL online time channel 1 LCD_TYPE_ONLINE_4='39 0 1 IP:' # Text LCD_TYPE_ONLINE_5='25 4 1' # DSL ip address LCD_TYPE_ONLINE_6='39 0 2 IN:' # Text LCD_TYPE_ONLINE_7='18 3 2' # DSL input rate LCD_TYPE_ONLINE_8='39 11 2 OUT:' # Text LCD_TYPE_ONLINE_9='19 15 2' # DSL output rate LCD_TYPE_ONLINE_10='39 0 3 >' # Text LCD_TYPE_ONLINE_11='34 1 3' # DSL quantity in channel 1 LCD_TYPE_ONLINE_12='39 11 3 <' # Text LCD_TYPE_ONLINE_13='37 12 3' # DSL quantity out channel 1 LCD_TYPE_OFFLINE_N='6' # no. of data types to show if offline LCD_TYPE_OFFLINE_1=' 0 0 0' # local date LCD_TYPE_OFFLINE_2=' 2 12 0' # local time LCD_TYPE_OFFLINE_3=' 39 0 1 CPU:' # Text LCD_TYPE_OFFLINE_4=' 38 4 1' # CPU LCD_TYPE_OFFLINE_5=' 39 9 1'% # Text LCD_TYPE_OFFLINE_6=' 40 0 2' # Text 1 LCD_VAR_TEXT_1='Text1' # Default-Text 1 -> /etc/lcd_text1.txt LCD_VAR_TEXT_2='Text2' # Default-Text 2 -> /etc/lcd_text2.txt LCD_VAR_TEXT_3='Text3' # Default-Text 3 -> /etc/lcd_text3.txt LCD_VAR_TEXT_4='Text4' # Default-Text 4 -> /etc/lcd_text4.txt ##----------------------------------------------------------------------------- ## register.txt - fli4l configuration parameters ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E D O C / D E U T S C H / O P T / R E G I S T E R . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E ## D O C / D E U T S C H / O P T / R E G I S T E R . T X T ## ## Creation: 14.02.2002 fm ## Last Update: 25.02.2002 jm ## ## Copyright (c) 2002 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: REGISTER #------------------------------------------------------------------------------ OPT_REGISTER='yes' # install fli4l registration: yes or no REGISTER_SERVER='eisler.fet.uni-hannover.de' # registration server REGISTER_ALWAYS='yes' # yes: each connect, no: once per day REGISTER_KEY='0x:0x:0x:0x:0x:0x' # your register key: see documentation! REGISTER_UPTIME='yes' # refresh your uptime: yes or no REGISTER_VERSION='yes' # send your fli4l version: yes or no REGISTER_NICK='Joachim_Berlin' # your nickname: may be empty REGISTER_CIRCUITS='pppoe' # circuit indices when to activate # registratiion, see documentation! #---------------------------------------------------------------------------- # seti.txt - optional opt_seti v 2.0 for fli4l version 2.0pre3 # # Creation: 01.10.2001 Lars Winkler # Last Update: 01.10.2001 Lars Winkler #---------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: setiathome #------------------------------------------------------------------------------ OPT_SETI='yes' # if yes, setiathome client is included SETI_START='yes' # if yes, setiathome starts at bootup SETI_BOOTTIME='120' # delay in seconds until seti starts at bootup SETI_BACKUP='yes' # if yes, a backup of workunit will be created # or an existing backup will be restored SETI_BACKUPTIME='18000' # seconds for backupinterval SETI_BACKUPDIR='/usr/local/data' # directory where to backup the workunit SETI_NICELEVEL='1' # Set "nice" priority ##----------------------------------------------------------------------------- ## time.txt - fli4l configuration parameters 2.0.3 ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 28.02.2002 jm ## ## Copyright (c) 2001 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: TIME #------------------------------------------------------------------------------ OPT_TIME='yes' # install time zone informations: yes or no TIME_ZONE='MET' # timezone: MET or GMT TIME_SERVICE='yes' # enable "time" service (port 37): yes or no TIME_SERVER='ptbtime1.ptb.de' # names of time servers, may be empty TIME_ACCESS_AT_BOOT_TIME='yes' # access time server at boot time: yes or no TIME_CIRCUITS='pppoe' # circuit indices when to activate time sync ##----------------------------------------------------------------------------- ## tools.txt - fli4l configuration parameters 2.0.3 ## ## P L E A S E R E A D T H E D O C U M E N T A T I O N , ## S E E R E A D M E . T X T ## ## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N ## L E S E N , S I E H E R E A D M E . T X T ## ## Creation: 26.06.2001 fm ## Last Update: 28.02.2002 jm ## ## Copyright (c) 2001 Frank Meyer ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Package tools #------------------------------------------------------------------------------ OPT_ARP='no' # install arp yes or no OPT_ATD='no' # install atd yes or no OPT_CRON='no' # install cron yes or no OPT_E3='yes' # install e3 yes or no OPT_FTP='yes' # install ftp yes or no OPT_IMONC='yes' # install imonc yes or no OPT_NETCAT='yes' # install netcat yes or no OPT_NETSTAT='no' # install netstat yes or no OPT_SORT='no' # install sort yes or no OPT_TAIL='no' # install tail yes or no OPT_TRACEROUTE='no' # install traceroute yes or no OPT_WGET='no' # install wget, see howto on www.fli4l.de ##----------------------------------------------------------------------------- ## tuxtime.txt - Configuration for TuxTime Client ## ## Creation: 08.02.2002 tobig ## Last Update: 16.03.2002 jm ## ## Copyright (c) 2002 Tobias Gruetzmacher ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ##----------------------------------------------------------------------------- #------------------------------------------------------------------------------ # Optional package: TuxTime Uptime Statistics #------------------------------------------------------------------------------ OPT_TUXTIME='yes' # install TuxTime TUXTIME_USER='JoMe' # your TuxTime username TUXTIME_PASS='xxx' # your TuxTime password TUXTIME_COMPID='1611' # your TuxTime computer id